A P1135 code on a Toyota Camry is an OBD-II (On-Board Diagnostic) trouble code that indicates a malfunction in the air-fuel ratio sensor (also known as an oxygen sensor or O2 sensor) heater circuit for Bank 1, Sensor 1.

This sensor is located on the exhaust manifold and is responsible for monitoring the air-fuel mixture in the engine. The heater circuit helps the sensor reach operating temperature more quickly, allowing for more accurate readings.

P1135 code on a Toyota Camry

Possible causes for a P1135 code include:

  1. A faulty air-fuel ratio sensor (Bank 1, Sensor 1)
  2. Damaged, shorted, or corroded wiring or connectors in the sensor’s heater circuit
  3. A blown sensor fuse
  4. A malfunctioning powertrain control module (PCM) or engine control module (ECM)

To diagnose and fix the issue, follow these steps:

  1. Visually inspect the wiring and connectors related to the air-fuel ratio sensor. Repair or replace any damaged components.
  2. Use a multimeter to check the resistance of the sensor’s heater circuit. If the resistance is out of the specified range (check the service manual for your specific model), replace the sensor.
  3. Check the sensor fuse and replace it if necessary.
  4. If the issue persists, consider consulting a professional mechanic for a more in-depth diagnosis, as there might be a problem with the PCM or ECM.

Remember to clear the code with an OBD-II scanner after fixing the issue to reset the check engine light.

P1135 code on a Toyota Camry possible causes

Table: P1135 code on a Toyota Camry possible causes and comments

Possible CauseComments
1. Faulty air-fuel ratio sensor (Bank 1, Sensor 1)This sensor monitors the air-fuel mixture in the engine; a malfunction can cause the P1135 code to be triggered.
2. Damaged, shorted, or corroded wiring/connectorsCheck the wiring and connectors related to the sensor’s heater circuit; repair or replace any damaged components.
3. Blown sensor fuseCheck the sensor fuse and replace it if necessary; a blown fuse may prevent the heater circuit from functioning.
4. Malfunctioning PCM or ECMIf other causes have been ruled out, consider consulting a professional mechanic for a more in-depth diagnosis.

Remember to clear the code with an OBD-II scanner after fixing the issue to reset the check engine light.

P1135 code on a Toyota Camry Tech Note

When diagnosing a P1135 code on a Toyota Camry, it is essential to follow the proper troubleshooting steps and keep the following technical notes in mind:

  1. A P1135 code indicates a malfunction in the heater circuit of the air-fuel ratio sensor (Bank 1, Sensor 1). This sensor is crucial for monitoring and adjusting the air-fuel mixture in the engine for optimal performance and emissions.
  2. Before replacing the air-fuel ratio sensor, make sure to inspect the wiring and connectors related to the sensor’s heater circuit. Damaged, shorted, or corroded wiring or connectors can cause the P1135 code and may need to be repaired or replaced.
  3. Verify that the sensor fuse is not blown. A blown fuse may prevent the heater circuit from functioning correctly, leading to the P1135 code.
  4. If the wiring and connectors appear to be in good condition, and the fuse is not blown, use a multimeter to check the resistance of the sensor’s heater circuit. Consult your vehicle’s service manual for the specified resistance range. If the resistance is out of the specified range, replace the sensor.
  5. If you have replaced the air-fuel ratio sensor and the P1135 code persists, consult a professional mechanic for further diagnosis. In rare cases, a malfunctioning powertrain control module (PCM) or engine control module (ECM) could be the root cause of the issue.
  6. After addressing the issue, clear the code with an OBD-II scanner to reset the check engine light and confirm that the problem has been resolved.

P1135 code on a Toyota Camry possible symptoms and solutions

Table: P1135 code on a Toyota Camry possible symptoms and solutions

Possible SymptomSolution
1. Check engine light illuminatedUse an OBD-II scanner to read and clear the code after fixing the issue to reset the check engine light.
2. Poor fuel economyReplace the faulty air-fuel ratio sensor or repair wiring/connectors, as needed.
3. Rough engine idleAddress the P1135 code issue by following the troubleshooting steps and repairing/replacing components.
4. Hesitation or lack of power during accelerationProperly diagnose and fix the P1135 code issue to improve engine performance.
5. Increased emissionsRepair or replace the faulty air-fuel ratio sensor or related components to decrease emissions.

These symptoms may be experienced when encountering a P1135 code on a Toyota Camry. Addressing the underlying issue with the air-fuel ratio sensor heater circuit should resolve these symptoms and improve overall vehicle performance.

P1135 code on a Toyota Camry Description

A P1135 code on a Toyota Camry is an OBD-II (On-Board Diagnostic) trouble code that relates to a malfunction in the air-fuel ratio sensor’s heater circuit for Bank 1, Sensor 1.

This sensor, also known as an oxygen sensor or O2 sensor, is crucial for monitoring and adjusting the air-fuel mixture in the engine, which helps maintain optimal performance and emissions.

The heater circuit within the sensor allows it to reach operating temperature more quickly, providing more accurate readings.

When a P1135 code is triggered, it means that the vehicle’s powertrain control module (PCM) or engine control module (ECM) has detected a problem with the air-fuel ratio sensor’s heater circuit in Bank 1, Sensor 1. This issue can lead to poor fuel economy, increased emissions, rough idling, hesitation during acceleration, and a check engine light illumination.

To address the P1135 code, it is important to follow proper troubleshooting steps, including checking the air-fuel ratio sensor, inspecting the wiring and connectors, verifying the sensor fuse, and consulting a professional mechanic if necessary. After resolving the issue, the check engine light can be reset using an OBD-II scanner.

How much does it cost to diagnose and fix the P1135 code on a Toyota Camry?

The cost to diagnose and fix the P1135 code on a Toyota Camry can vary depending on several factors, such as your location, the specific issue causing the code, and whether you choose to do the work yourself or have it done by a professional mechanic. Here’s a general cost breakdown:

  1. Diagnostic cost: The cost to diagnose the P1135 code using an OBD-II scanner can range from $50 to $100 if you go to a professional mechanic or repair shop. However, you can purchase an affordable OBD-II scanner for around $20 to $50 and diagnose the code yourself.
  2. Replacement air-fuel ratio sensor: If the sensor is determined to be faulty, a replacement air-fuel ratio sensor for a Toyota Camry can cost between $100 and $250 for the part, depending on the make and model year of your vehicle. Labor costs can range from $50 to $150, depending on your location and the hourly rate of the mechanic.
  3. Wiring and connector repair: If the issue is related to damaged wiring or connectors, the cost for parts will likely be relatively low, but labor costs can vary depending on the complexity of the repair and the time required.
  4. Fuse replacement: If the issue is a blown fuse, the cost of a new fuse is minimal, usually less than $5. The labor cost to replace the fuse will depend on the mechanic’s hourly rate and how accessible the fuse is.
  5. PCM or ECM repair/replacement: In rare cases, the problem may be related to a malfunctioning PCM or ECM. Repairing or replacing these components can be expensive, with costs ranging from several hundred to over a thousand dollars, including parts and labor.

In summary, the total cost to diagnose and fix the P1135 code on a Toyota Camry can range from around $50 (for a DIY fuse replacement) to over a thousand dollars (for a professional PCM or ECM repair/replacement). Keep in mind that these costs are approximate and can vary based on your specific situation.

How to fix the P1135 code on a Toyota Camry?

To fix the P1135 code on a Toyota Camry, follow these steps:

  1. Scan for codes: Use an OBD-II scanner to confirm the P1135 code and check for any additional related codes.
  2. Visually inspect wiring and connectors: Inspect the wiring and connectors related to the air-fuel ratio sensor’s heater circuit (Bank 1, Sensor 1). Look for damaged, corroded, or shorted wires and connectors. Repair or replace any damaged components as needed.
  3. Check the sensor fuse: Locate the fuse associated with the air-fuel ratio sensor’s heater circuit and check if it is blown. Replace the fuse if necessary.
  4. Test the air-fuel ratio sensor: Use a multimeter to check the resistance of the sensor’s heater circuit. Refer to your vehicle’s service manual for the specified resistance range. If the resistance is out of the specified range, replace the sensor.
  5. Clear the codes and test drive: After fixing the issue, clear the P1135 code using the OBD-II scanner and reset the check engine light. Test drive the vehicle to ensure that the problem is resolved and the code does not return.
  6. Consult a professional mechanic: If the issue persists after following these steps, consider consulting a professional mechanic for a more in-depth diagnosis. In rare cases, a malfunctioning powertrain control module (PCM) or engine control module (ECM) may be the root cause of the issue, and a professional mechanic can help determine and fix the problem.

Remember, it is essential to address the P1135 code as soon as possible to avoid potential damage to the engine or emissions system and ensure optimal performance and fuel economy.

Takeaways

When addressing a P1135 code on a Toyota Camry, keep these key takeaways in mind:

  1. A P1135 code indicates a malfunction in the heater circuit of the air-fuel ratio sensor (Bank 1, Sensor 1).
  2. Possible causes include a faulty air-fuel ratio sensor, damaged wiring or connectors, a blown sensor fuse, or a malfunctioning PCM or ECM.
  3. Symptoms of a P1135 code can include a check engine light, poor fuel economy, rough engine idle, hesitation during acceleration, and increased emissions.
  4. To diagnose and fix the issue, follow these steps: scan for codes, inspect wiring and connectors, check the sensor fuse, test the air-fuel ratio sensor, and consult a professional mechanic if necessary.
  5. The cost to diagnose and fix the P1135 code can vary depending on factors such as your location, the specific issue, and whether you choose a DIY approach or professional help.
  6. Addressing the P1135 code promptly can help maintain optimal engine performance and fuel economy, and prevent potential damage to the engine or emissions system.