A P0135 code on a Honda Civic refers to an issue with the Oxygen (O2) sensor heater circuit malfunction for the bank 1 sensor 1. The O2 sensor monitors the levels of unburned oxygen in the exhaust gases, which helps the engine control module (ECM) to adjust the air-fuel mixture for optimal combustion and fuel efficiency.

P0135 code on a Honda Civic

Bank 1 refers to the side of the engine where the first cylinder is located, while sensor 1 indicates that it is the pre-catalytic converter sensor (upstream).

The P0135 code can be caused by several factors:

  1. Faulty O2 sensor: The sensor itself may be malfunctioning, which can trigger the code.
  2. Damaged or corroded wiring: The wires connecting the O2 sensor to the ECM may be damaged or corroded, causing a poor connection.
  3. Bad sensor heater: The heater element in the O2 sensor may be malfunctioning, causing the sensor to not reach its optimal operating temperature quickly enough.
  4. Faulty fuse or relay: The O2 sensor’s heater circuit may have a blown fuse or a faulty relay.
  5. Malfunctioning ECM: A rare occurrence, but it is possible that the ECM itself is malfunctioning and causing the code.

To fix the P0135 code on a Honda Civic, follow these steps:

  1. Inspect the wiring: Check for any damaged, corroded, or loose wiring around the O2 sensor. Repair or replace the wiring as necessary.
  2. Test the O2 sensor: Use a multimeter to test the O2 sensor’s resistance. Compare the readings to the manufacturer’s specifications. If it’s out of range, replace the sensor.
  3. Check the fuse and relay: Inspect the fuse and relay associated with the O2 sensor’s heater circuit. Replace them if necessary.
  4. Test the ECM: If all other components seem to be functioning correctly, consider having the ECM tested by a professional to ensure it is not causing the problem.

After addressing the issue, clear the code using an OBD-II scanner and test drive the vehicle to ensure the code does not reappear. If the code persists, consult a professional mechanic for further diagnosis and repairs.

P0135 code on a Honda Civic possible causes

Table: P0135 code on a Honda Civic possible causes and comments

Possible CauseComments
Faulty O2 sensorThe O2 sensor may be malfunctioning, causing incorrect readings or heater circuit issues. Replace the sensor if necessary.
Damaged or corroded wiringThe wiring connecting the O2 sensor to the ECM may be damaged, corroded, or loose. Repair or replace the wiring as needed.
Bad sensor heaterThe heater element in the O2 sensor may be malfunctioning, causing the sensor to not reach its optimal operating temperature quickly enough. Replace the sensor if the heater is faulty.
Faulty fuse or relayThe O2 sensor’s heater circuit may have a blown fuse or a faulty relay. Inspect and replace them if necessary.
Malfunctioning ECMA rare occurrence, but the ECM itself may be malfunctioning and causing the code. Have the ECM tested by a professional if all other components are functioning correctly.

P0135 code on a Honda Civic Tech Note

Tech Note for P0135 code on a Honda Civic:

When diagnosing a P0135 code on a Honda Civic, it is essential to consider the following:

  1. Verify the code: Use an OBD-II scanner to verify the P0135 code and check for any other related codes that may provide additional information about the issue.
  2. Visual inspection: Perform a thorough visual inspection of the O2 sensor, its wiring, and surrounding components for any visible damage or corrosion.
  3. Manufacturer-specific information: Consult the service manual or technical service bulletins (TSBs) for your specific Honda Civic model and year to determine if there are any known issues or recommended diagnostic procedures.
  4. Test components: Use a multimeter and appropriate diagnostic tools to test the resistance and voltage of the O2 sensor, its heater circuit, and related components, such as fuses and relays.
  5. Monitor live data: With the engine running and at operating temperature, monitor the O2 sensor’s live data using an OBD-II scanner to ensure it is functioning properly and providing accurate readings.
  6. Reset and retest: After addressing the issue, clear the code using an OBD-II scanner and test drive the vehicle to ensure the code does not reappear.

Remember that patience and attention to detail are crucial when diagnosing and repairing a P0135 code on a Honda Civic. If you are not confident in your ability to diagnose and repair the issue, consult a professional mechanic for assistance.

P0135 code on a Honda Civic possible symptoms and solutions

Table: P0135 code on a Honda Civic possible symptoms and solutions

Possible SymptomsSolutions
Check Engine Light illuminatedUse an OBD-II scanner to read and clear the code after addressing the issue.
Poor fuel economyFix the O2 sensor issue to ensure proper air-fuel mixture management and improve fuel efficiency.
Rough idling or engine hesitationAddress the O2 sensor issue to ensure proper air-fuel mixture management, improving engine performance and reducing rough idling.
Increased emissionsReplace or repair the faulty O2 sensor to help the ECM manage air-fuel mixture effectively, resulting in reduced emissions.
Difficulty passing an emissions testAddress the O2 sensor issue to ensure proper emissions management and increase the chances of passing an emissions test.

Note: The above table lists possible symptoms and corresponding solutions related to a P0135 code on a Honda Civic. Keep in mind that these symptoms can also be associated with other issues, and a proper diagnosis is necessary to confirm the cause.

P0135 code on a Honda Civic Description

The P0135 code on a Honda Civic is a diagnostic trouble code (DTC) related to the oxygen (O2) sensor heater circuit malfunction for bank 1 sensor 1.

The O2 sensor is a crucial component in the engine management system, responsible for monitoring the levels of unburned oxygen in the exhaust gases. This information helps the engine control module (ECM) to adjust the air-fuel mixture for optimal combustion, fuel efficiency, and reduced emissions.

Bank 1 refers to the side of the engine containing the first cylinder, and sensor 1 indicates the pre-catalytic converter sensor (upstream).

The O2 sensor contains a heater element that helps it reach its optimal operating temperature quickly. This ensures accurate measurements even when the engine is cold. The P0135 code indicates that there is a problem with the O2 sensor’s heater circuit, affecting the sensor’s ability to function properly.

Possible causes for the P0135 code include a faulty O2 sensor, damaged or corroded wiring, a bad sensor heater, a faulty fuse or relay, or a malfunctioning ECM.

To diagnose and fix this issue, a thorough inspection of the O2 sensor, wiring, and related components is required, along with the use of an OBD-II scanner and a multimeter to test the resistance and voltage of the components.

How much does it cost to diagnose and fix the P0135 code on a Honda Civic?

The cost to diagnose and fix the P0135 code on a Honda Civic can vary depending on your location, the specific issue, and whether you choose to do the work yourself or have it done by a professional mechanic. Here are some general cost estimates for diagnosing and repairing the P0135 code:

  1. Diagnostic cost: The diagnostic cost can range from $80 to $120 at a repair shop. Some auto parts stores may offer to read the codes for free, but a professional mechanic will typically perform a more comprehensive diagnosis.
  2. O2 sensor replacement: If the issue is a faulty O2 sensor, the cost to replace it can range from $150 to $350, including parts and labor. The price of the O2 sensor itself can vary depending on the brand and quality, generally ranging between $50 and $100.
  3. Wiring repair or replacement: If the issue is related to damaged or corroded wiring, the repair cost can vary depending on the extent of the damage. Minor repairs may cost $50 to $100, while more extensive wiring replacements can cost several hundred dollars.
  4. Fuse or relay replacement: If the problem is a blown fuse or a faulty relay, the replacement cost is usually low, around $20 to $50, including parts and labor.
  5. ECM repair or replacement: If the issue is related to a malfunctioning ECM, the cost to repair or replace it can be quite high. ECM replacement can range from $500 to $1,500 or more, including parts and labor.

Please note that these are only general cost estimates, and actual costs can vary depending on factors such as your vehicle’s make, model, and year, the labor rates in your area, and any additional work that may be required. Always obtain a detailed quote from your mechanic to get a better understanding of the specific costs associated with diagnosing and fixing the P0135 code on your Honda Civic.

How to fix the P0135 code on a Honda Civic?

To fix the P0135 code on a Honda Civic, follow these steps:

  1. Verify the code: Use an OBD-II scanner to read the stored codes in your vehicle’s ECM. Make sure the P0135 code is present and check for any other related codes that may provide additional information.
  2. Visual inspection: Conduct a thorough visual inspection of the O2 sensor (bank 1, sensor 1), its wiring, and surrounding components. Look for any visible signs of damage, corrosion, or loose connections.
  3. Test the O2 sensor: Using a multimeter, test the resistance of the O2 sensor’s heater element. Compare your readings to the manufacturer’s specifications. If the resistance is out of range, consider replacing the sensor.
  4. Inspect the wiring: Check the wiring connecting the O2 sensor to the ECM for any signs of damage, corrosion, or loose connections. Repair or replace the wiring as necessary.
  5. Check the fuse and relay: Inspect the fuse and relay associated with the O2 sensor’s heater circuit. Replace them if necessary.
  6. Test the ECM: If all other components seem to be functioning correctly, consider having the ECM tested by a professional to ensure it is not causing the problem.
  7. Clear the code and test drive: After addressing the issue, use an OBD-II scanner to clear the P0135 code. Test drive the vehicle to ensure the code does not reappear and that the problem has been resolved.

Keep in mind that each case may be different, and additional diagnostic steps may be required based on your specific Honda Civic model and year. If you are not confident in your ability to diagnose and repair the issue, consider consulting a professional mechanic for assistance.

Takeaways

When dealing with a P0135 code on a Honda Civic, remember the following takeaways:

  1. The P0135 code refers to an issue with the oxygen (O2) sensor heater circuit malfunction for bank 1 sensor 1.
  2. This code can be caused by a faulty O2 sensor, damaged or corroded wiring, a bad sensor heater, a faulty fuse or relay, or a malfunctioning ECM.
  3. To fix the issue, verify the code, perform a visual inspection, test the O2 sensor, inspect the wiring, check the fuse and relay, and test the ECM if necessary.
  4. After addressing the issue, clear the code using an OBD-II scanner and test drive the vehicle to ensure the code does not reappear.
  5. Costs to diagnose and fix the P0135 code can vary depending on the specific issue and whether you choose to do the work yourself or have it done by a professional mechanic.
  6. If you are not confident in your ability to diagnose and repair the issue, consider consulting a professional mechanic for assistance.

By following these takeaways, you can effectively diagnose and fix the P0135 code on your Honda Civic, ensuring optimal engine performance, fuel efficiency, and reduced emissions.

Other Honda Civic Codes you Might Want to Check

P0128 code on Honda CivicP0497 code on Honda Civic
P1457 code on Honda Civic
P0420 code on Honda Civic